A Viking oven with model number VGIC 365 6BSS that does not reach temperature, bakes unevenly, or does not respond to the controls needs a diagnosis before a repair. This page lists the common symptoms, the likely causes, and what a technician checks.
Bonita Appliance Repair has repaired ovens in San Diego County since 2012. See Viking appliance repair for the Viking services we offer, and oven repair in San Diego for our general oven service.
Confirm your model and fuel type
The model number is on the data plate, usually on the oven frame or the door edge. Check that it reads VGIC 365 6BSS, and note the fuel type listed in your owner’s manual. The likely causes depend on whether the oven heats with gas or electricity.
See how to find your appliance model number if you cannot locate the plate.
Stop using the oven if you smell gas
Do not turn any switch on or off. Leave the house, and call SDG&E at 1-800-411-7343 or 911 from outside. Do not use the oven until a technician inspects it.
The oven does not reach temperature
An oven that stays far below the set temperature has a heating fault. Compare the dial setting with an oven thermometer on the center rack.
- Gas ovens: a weak igniter can fail to open the gas valve fully, so the burner produces little heat. Igniters weaken with age.
- Electric ovens: a worn bake element, a failed temperature sensor, or a control board fault
A technician tests the igniter or element with a meter. The technician also confirms the correct part for your model.
The oven bakes unevenly
Uneven results can come from a worn element, a failing temperature sensor, a damaged door gasket, or a thermostat that is out of calibration. Place an oven thermometer on the center rack, and compare it with the set temperature after 20 minutes.
The door does not close or seal
Check the hinges for damage or misalignment, and check the gasket for tears. A door that does not close fully lets heat escape and can trigger error codes. A technician can adjust the hinges or replace the gasket.
The control panel does not respond
- Check that the oven has power. Confirm the circuit breaker has not tripped.
- Check whether the controls are locked. Look for a lock indicator on the display.
- Turn off the oven’s circuit breaker, wait 5 minutes, and turn it back on.
- If the panel still does not respond, call a technician. The control board or the touchpad may have failed.
What an oven repair costs
At Bonita Appliance Repair, a typical oven repair costs $130 to $400. Common repairs have these typical ranges:
- Bake or broil element: $180 to $320
- Gas igniter: $220 to $380
- Temperature sensor or thermal fuse: $180 to $280
- Control board: $250 to $400
The diagnostic fee is $80 to $90, and we usually waive it if you approve the repair. A technician gives you the price before any work begins.
Frequently asked questions
Why is my Viking oven not reaching temperature?
In a gas oven, a weak igniter is a common cause. In an electric oven, check the bake element and the temperature sensor. A technician can test each part.
How do I find the model number of my Viking oven?
The data plate is usually on the oven frame or the door edge. Open the door and look for a label with the model and serial numbers.
Can I replace a Viking oven igniter myself?
Igniter replacement involves electrical and gas connections. Turn off the power and the gas supply before you work on the oven. A technician can confirm the igniter is the cause and fit the correct part.
How much does it cost to repair a Viking oven?
At Bonita Appliance Repair, a typical oven repair costs $130 to $400. The diagnostic fee is $80 to $90, and we usually waive it if you approve the repair.
Does Bonita Appliance Repair repair Viking ovens?
Yes. Bonita Appliance Repair repairs Viking ovens in San Diego County. Call 619-329-5938 or book online.
Book Viking oven repair in San Diego
Bonita Appliance Repair finds the cause of the oven problem and explains the repair and its price before any work begins.
